Asphalt Batch Mix Plant is a plant used for the manufacture of asphalt, macadam and other forms of coated road stone, sometimes collectively known as blacktop.
The manufacture of coated road stone demands the combination of a number of aggregates, sand and a filler (such as stone dust), in the correct proportions, heated, and finally coated with a binder, usually bitumen based or, in some cases, tar. The temperature of the finished product must be sufficient to be workable after transport to the final destination. A temperature in the range of 100 - 200 degrees Celsius is normal.
Increasingly, recycled asphalt pavement (RAP) is used as part of the mix. The binder used is flammable, and the heaters are large liquid or gas fired burners. RAP is introduced after the heating process and must be accounted for in the overall mix temperature calculations.
There are three main classes of plant: batch heater, semi-continuous (or "asphalt plant"), and continuous (or "drum mix"). The batch heater has the lowest throughput, the continuous plant the highest at up to around 500 Tonnes per hour.
Supply of road stone for large contracts is generally by tender with considerable pressure on price. A faulty batch of road stone must be planed up and relaid, often with additional lane rental charges, at a cost which may be orders of magnitude higher than the original price, so sophisticated control systems are a necessity.
One key ingredient of most road stones is sand. Sand generally has a high water content. Boiling off this water is a large part of the energy cost of heating the aggregate, in turn a significant part of the overall cost of operation. The water content of sand also varies considerably, especially when stored outdoors, being typically of the order of some tens of percent of the overall mass of wet sand. Since sand takes the form of small grains, with a high surface area per unit volume, and binder attaches to the surface of the aggregates, the amount of dry sand in the mix is particularly critical to the overall blend; the moisture content must be measured and the equivalent dry weight calculated.
Binder comes in different grades known as "penetration" or "pen" grades, with values varying between around 30 and 300. The pen value is an expression of the depth to which a standard needle will penetrate the surface of the binder at a specified temperature (the higher the value, the softer the binder). This has an effect on the work ability of hot asphalt and the stiffness of the asphalt when cooled. Lower pen values give harder wearing. Asphalt wearing courses are typically 35-50 pen, base courses will be higher, typically 200 or 300 pen. The coating plant may combine binder of different grades to achieve a grade between those held on site.
Filler, as the name implies, fills the voids between aggregate grains and improves the wearing capabilities of the overall mix. It is stored and fed dry into the mix, during or after addition of binder. A common source of filler is fines from the heating process recovered by bag filters or wet filtration ponds from the exhaust of the heating drum.
Types of Plant
Batch Heater: A batch heater plant weighs the raw aggregates into a heater drum, where the batch is then heated up to temperature. The hot aggregate is discharged into a mixing drum where (dry) filler and binder are added. The blend is mixed and discharged either directly into the delivery vehicles or into a small weighing and collecting hopper. To increase output, the heater can be heating the next batch while the previous is being mixed. Capacity is usually of the order of tens of tonnes per hour.
Batch heater plant is used where short production runs are common (a different recipe can be used on each mix) or where total volume is low. Mobile batch heaters are available.
Continuous: In the continuous plant, raw aggregate is brought up from ground hoppers at a precisely controlled rate and fed into a heater drum similar to that used in the asphalt plant. Once heated it is immediately coated in the same drum (with the binder spray bars situated behind the burner) or in a smaller drum situated immediately behind it. Finished product is almost invariably discharged into a hot store rather than directly into delivery vehicles.
Changing mix is achieved by varying the feed rates of the aggregate, filler and binder feeders, with time delays so that the change of blend occurs at the same point in the coating drum. Sand tends to move more slowly through the heating drum, so the blend proportions will not necessarily change at the same point on the feed conveyor. It is common to divert a small amount of material to a waste chute when the transition point reaches the hot elevator.
Drum mix plants are not really suitable for short production runs; although with sophisticated controls the change of mix can be accurate to within some seconds, production rates of hundreds of tonnes per hour may equate to a tonne every ten seconds or so.
Finished road stone must be kept heated to avoid setting. It is commonly stored in large electrically heated insulated stainless steel silos, from which it is weighed into delivery vehicles. This may be achieved by intermediate weigh hoppers (which may shuttle between hoppers) or by mounting the hoppers directly on load cells. Control of load-out by this method involves accurately predicting the material "in flight" between the discharge door and the vehicle.
Precise control is a necessity. Asphalt Batch mixing and load-out plant typically use a combination of industrialized computer control and programmable logic controllers to achieve this.
With asphalt being a real-time product, timing is important when it comes to delivering product amounts to job sites, etc... 2008 has provided plants with a level of control over equipment by utilizing GPS, RFID and other forms of tracking systems. Tracking provides information throughout the supply chain to make sure that the right amount and type of product is delivered to the correct site in a timely manner and with better accuracy.